Aquameta™ PG420-0.5VFU

Glue in pressure transducer for UPVC/CPVC pipe fittingst

  • Description
  • Technical specifications
  • Downloads

The CP420 series of 4-20mA pressure transducers are a cost effective and robust solution designed to be glued into UPVC or CPVC pipe fittings using the appropriate solvent cement and methods. It is suitable for use with chemicals such as Sodium Hypochlorite, Sulfuric and Hydrochloric acid. It may be used with other chemicals that are compatible with its wetting materials which are UPVC/CPVC, Viton,FEP and PTFE. Different choice of seals is available for other chemicals. The PG420-0.5VFU is suitable for pressure application of 0.5 bar. A 1 bar option is available. The PG420 series is a fully sealed device that can be submerged. This makes it ideal for use within bunded locations where the possibility exists that the transducer may become submerged. Typically the PG420 series transducer is glued into a flanged fitting that is part of a ball valve, this means that the transducer can be isolated to facilitate installation and maintenance.

Transducer Construction
This state of the art pressure sensor uses a flush Aluminum Oxide Ceramic diaphragm in conjunction with on-board signal conditioning to measure pressures. Pressure and temperature calibration is done electronically with the internal application-specific integrated circuit (ASIC). When pressures and temperatures change, the electronics provide an offset and span correction. It also includes aging detection and compensation. This new method guarantees good precision and long term stability. The sensor is encapsulated in a UPVC body that is filled with an epoxy. The sensor cable is molded into the transducer eliminating problems associated with threaded plugs. This design ensures a very high level of reliability. The outer diameter of the probe is 26.67mm suitable to be glued into ¾” pipe fittings.

Features

  • UPVC housing to suit ¾” pipe fittings.
  • 4-20mA output
  • 9 to 30V
  • Temperature compensated
  • Barometric pressure compensation via vented cable
  • High linearity and low hysteresis values
  • EMI Certified
  • Excellent resistance to corrosion and abrasion
  • Automated offset and span correction
  • Age compensation
  • Spigot flange to protect pressure sensing surface from run off glue
  • Rounded front shoulder to prevent glue being scraped off the fitting as the transducer is inserted
  • Compact unit, suitable for use in confined spaces

Output Signals
The PG420 transducer uses a two wire 4-20mA output signal. The signal is linear with pressure. The sensor will operate with a supply voltage that can range from 9V to 30V DC. The Aquameta Junction box may be used to extend the transducer cable with any other cable. The vented junction box has a Gortex covered opening that allows venting to atmosphere to take place whilst restricting the ingress of moisture.

Ordering
PG420-0.5VPU
Housing: U = UPVC, C= CPVC
Cable: P=PVC, F=FEP
Seals: V=Viton, N=Nitrile, K=Kalrez, E= EPDM
Pressure: 0.5, 1, 10 bar

Input pressure range
Nominal pressure gauge [bar]    0.5    1
Level [mH2O]    5    10
Overpressure [bar]    1    2
Burst pressure ≤ [bar]    2    4

Output signal / Supply
Standard 2-wire: 4… 20 mA/Vs = 9 … 35Vdc

Performance
Accuracy    ≤ ± 0.5% FSO
Permissible load    Rmax = [(Vs – 9)/0.02A]Ω
Influence effects    Supply: 0.05 % FSO/10V    Load: 0.05 % FSO /kΩ
Long term stability [%FS/year]    ≤ ± 0.3 @ 25 [°C]
Response time    ≤ 5ms

Thermal Effects(Offset and Span)
Thermal error ≤ 0.007mA/10[°C]

Permissible temperatures
Medium: -25/+65[°C]    Storage: -40/+135[°C]

Electrical protection
Short-circuit protection    Permanent
Reverse polarity protection    No damage – no function
Norms compliance    Radiated electromagnetic field IEC/EN 61000-4-3(2006)    Electrical fast transition burst IEC/EN 61000-4-4(2004)    RF conducted disturbances IEC/EN 61000-4-6(2006)
RoHS compliance    RoHS

Electrical connection
Cable with sheath material     PVC (0 … 65°C) black
Standard cable length     10m (Custom cable lengths available)

Materials (media wetted)
Housing     U-PCV grey
Seals     Viton
Diaphragm     PTFE

Miscellaneous
Current consumption     Min 3.8mA Max 20.4mA
Weight     ± 135g (without cable)
Ingress protection     IP 68
Country of origin     Australia
Warranty      3 Years

The following downloads are available for the Aquameta™ PG420-0.5VFU
Download Aquameta™ PG420-0.5VFU PDF